Why is my wood burning stove "ticking" and "clicking"?

Ticking or banging noises are a common characteristic of metal stoves and are generally due to the metal expanding in the heat generated by the combustion and as such can also be a useful indicator of the intensity of the combustion. Many people experience this ‘ticking’ or ‘clicking’ as part of the comfort of having a stove. The tensions will decrease over time and can be minimised by firing up the stove a few times.

Ticking noises are a common characteristic of stoves made of sheet iron and are caused by the expansion of the iron as it heats up. The sounds are most common during ignition and firing, as well as during cooling. If the sounds become very frequent once the stove has warmed up, it may be a sign that the stove is overheating or needs some minor adjustments. New stoves tend to make a lot of noise during the first few fires until the metal has set. The noise will diminish over time and can be minimised by firing up the stove a few times.

Make sure the stove is not overheating

1. Make sure the Aduro-tronic is used according to the procedure in the user manual. The damper should stay in the initial (closed) position except during firing up or reloading. Only use the Aduro Key to keep the damper open when lighting up the stove.
2. Check that your installation is done according to the instructions in the manual. The ideal draft is around 12 Pa. If the draft is too high, it is often possible to hear wind howling coming from the stove. The draft can be reduced by installing a pipe damper or a different chimney cowl.

Do not overload

Consult the user manual of the stove to check the maximum quantity of wood. In most Aduro stoves, there is an indication of maximum load. Use this indication as a reference when loading the stove. Always load the stove below the max load indication.

Use the correct kind of wood

The stove is designed to operate with firewood with a moisture between 10% and 18%. If the wood is too dry and in small pieces, it might produce too much heat.

Use the correct combustible

Make sure to burn only seasoned firewood that is designed for the use in wood burning stoves. Pellet, wood shavings or other alternative products are not ideal for use.

Use the correct size of wood

Use a mix of small and big logs. If the stove is loaded with too many small pieces, it will overheat.

Reduce the noise

To reduce the noise it is possible to try the following adjustments. Please note that not all stoves are fitted with removable back/baffle plate. Most of them have at least one of the two options.

WARNING: The following must be conducted when the stove is cold.

Loosen the back plate slightly

The back plate is often the largest single metal sheet in the stove and as such, can make some noises when exposed to heat. To decrease the tension in the metal do as follows:

1. Locate the back-plate screws on your stove. Most stoves are fitted with a removable back plate, hold in position by screws. Screws are usually on the top and bottom part of the back plate.
2. Untie the screws. Make sure that the back plate is still attached firmly to the stove, but at the same time has some extra tolerance to allow extra expansion.

Loosen the metal baffle plate slightly

The metal baffle plate is directly exposed to a very high heat and as a result can expand beyond the normal tolerances. For some Aduro stoves, the metal baffle plate is attached to the stove with bolts. To decrease the tension in the metal, please proceed as follows:

1. Locate the metal baffle plate in the stove. To access the metal baffle plate, gently remove the top vermiculite plate from the combustion chamber.
2. Untie the bolts. Make sure that the metal baffle plate is still attached firmly to the stove, but at the same time has some extra tolerance to allow extra expansion.

Verwarm maximaal in de kachel

Wanneer het metaal van de kachel aan hoge warmte wordt blootgesteld, zet het metaal zich. Wanneer dit nog niet is gebeurd, zal de kachel vaak tikken. Het is mogelijk om dit proces te versnellen door zeer krachtig op te stoken in de kachel voor een beperkte periode. Dit doet u als volgt:

1. Vul de kachel met de maximale hoeveelheid brandhout (zie de handleiding)
2. Steek aan en gebruik de Aduro sleutel om de primaire klep open te houden tijdens het stoken. Dit zal extra zuurstof aan het vuur geven en de temperatuur laten stijgen.

Omdat deze manier van stoken de constructie van de kachel belast, wordt dit alleen aanbevolen wanneer het strikt noodzakelijk is. Een of twee keer op deze manier stoken is voldoende om het metaal te laten zetten.